Resource library

Substation drafting guides

Drawing structures, review boundaries and handover controls for HV project teams.

guide

Does the full OTDR trace length equal the installed fiber length?

A substation fiber worksheet separates OTDR reference cables from installed link length using a fictional distance axis and explicit endpoint markers.

guide

Does a blocked spanning-tree port mean the cable is disconnected?

A substation network evidence worksheet distinguishes installed links from spanning-tree forwarding state without changing network or protection settings.

guide

Does a VLAN number prove that every frame on a link is tagged?

A substation communications drawing worksheet separates VLAN membership, wire tagging and port behavior without changing network or protection settings.

guide

Does an LC connector identify single-mode or multimode fiber?

A substation optical-link register separates connector, fiber mode, transceiver and operating basis before a drawing handover is accepted.

guide

Does an ICD file prove the installed IED configuration?

An IEC 61850 handover register separates ICD, CID and SCD roles, device identity and approved revision without treating a filename as proof of commissioning.

guide

Should an IED port MAC address and IP address share one drawing field?

A substation IED network worksheet keeps equipment identity, physical interface, MAC record, IP record and configuration revision distinct.

guide

How should calculated and measured residual current be distinguished on drawings?

A substation drawing worksheet distinguishes calculated residual current, dedicated measurement inputs and model-specific configuration evidence.

guide

Is relay contact carrying current the same as its switching rating?

An original protection and control drawing worksheet separates relay contact make, break and continuous ratings from coil supply requirements.

guide

Is nominal relay coil voltage the same as its operating range?

An original substation control drawing worksheet separates coil identity, nominal voltage, permitted operating range and the approved supply assessment.

guide

How should CT input burden and impedance be separated in drawing records?

An original substation drawing worksheet connects current-input burden, impedance and current basis with a synthetic squared-current calculation.

guide

How should a latched relay output and its reset basis be shown in drawing records?

An original relay drawing consistency worksheet separating contact state, latching behavior, reset references and approved configuration evidence.

guide

How should phase-to-phase and phase-to-neutral VT voltages be recorded?

An original VT drawing review register separating voltage magnitude, phase reference, primary and secondary bases, approved connections and unresolved relay inputs.

guide

How should CT primary and secondary ratings be checked on drawings?

An original substation drafting worksheet for CT primary and secondary current ratings, ratio scaling and approved relay-interface evidence.

guide

Why is a relay logic input name not its terminal number?

A substation protection drafting matrix linking logical input names, physical terminals, device variants and approved signal sources.

guide

How should duplex fiber transmit and receive paths be traced on a substation drawing?

A substation communications drawing worksheet tracing duplex Tx/Rx endpoints, patch interfaces, viewing direction and approved fiber identities.

guide

Does a normally closed relay contact mean an alarm is active?

A drawing worksheet distinguishing single-stable relay contact states, selected terminals and approved alarm interpretation without changing wiring or logic.

guide

Does a spare terminal label mean the terminal is electrically unconnected?

A substation drawing worksheet separating terminal allocation, external wiring and documented bridge connections without treating spare as safe isolation.

guide

How should CT polarity markings be traced across substation drawings?

A current transformer polarity evidence worksheet comparing the selected device markings, approved schematic and terminal records without prescribing wiring.

guide

How should protection terminal cross-references be checked in substation drawings?

A terminal-to-destination worksheet for comparing protection schematics, cable schedules and terminal plans without approving wiring or settings.

guide

What should a substation drawing package contain?

A source-controlled structure for HV substation drawing sets.

guide

How should a protection and control schematic be checked?

A review sequence for substation protection, trip and control schematics.

guide

What should a substation general arrangement show?

A practical review structure for substation plans and elevations.

guide

How should as-built substation drawings be updated?

A controlled method for updating HV drawings after construction changes.

guide

How should HV drawing revisions be controlled?

Revision and issue controls for substation drawing production.

guide

How should a substation cable schedule be drafted?

A source-controlled cable schedule structure for HV substations.

guide

What should a substation protection panel layout show?

A coordination guide for protection and control panel drawings.

guide

What should a substation grounding drawing contain?

A documentation structure for substation grounding plans and details.

guide

How should a relay panel schematic be coordinated?

A source-linked review method for relay and protection schematics.

guide

How should substation as-built drawings be updated?

A verified evidence workflow for HV as-built drawing updates.

guide

What should a substation drawing register contain?

A drawing-control structure for substation design and drafting sets.

guide

How should a switchyard plan and profile be reviewed?

A coordination method for switchyard plans, elevations and interfaces.

guide

How should a substation interface register be built?

A responsibility register for HV electrical, civil and controls interfaces.

guide

How should HV drawing document control work?

A revision, source and issue method for high-voltage drawing sets.

guide

How should an electrical drafting markup review work?

A review method for converting engineering markups into controlled drawings.

guide

What should a substation single line diagram show?

A practical content and review checklist for a substation single line diagram.

guide

What do electrical CAD services deliver?

The file, checking and scope standards to expect from electrical CAD services.

guide

What is the difference between substation design and drafting services?

A clear scope boundary between substation engineering design and drafting services.

guide

How do electrical drafting services work for HV projects?

A practical workflow for outsourced HV and substation electrical drafting services.

guide

How do you review a switchroom layout?

A drawing review method for switchroom general arrangements without inventing project clearances.